What Is Your Favorite FLAVOR RDA?

So I bought a couple of VAMP Duallys hoping they would be good flavor RDAs. Though they're not bad, I would consider them more of a cloud atty. But I'm looking to add a few more flavor attys to my collection.

So, the question of the day is, what's your favorite flavor producing RDA?

Right now, my current 2 favorites are the Petri V2 and the Derringer.
EDIT: Forgot about my Goon clones. Definitely good flavor from these.

Wismec Neutron

This is my first dripper so obviously I can not compare much but having said that I can not fault it.
No bottom airflow so no leaking, velocity style deck and top aiflow work great.
I started with a simple dual coil setup ss316l 9 wraps came out at .29, although my wicking needs much improvement I'm more than happy with my first attempt.

Ended up towards 53 joules 555°F. I will have to try to try some twisted coils on next as the flavour or clouds weren't as good as I expected.

Open to…

Wismec Neutron

Help with Crius RTA

So I got the obs crius 25mm rta and for the life odd me I can't figure how to build this this. First build was 2.0 id with 24g kanthal @7 wraps for .25 ohm, wicked our with rayon and wicks barely in the channels and powered it at 50 watts and hardly no taste and vapor, bumped it to 55 and dry hits. So I rebuild and go to 2.5 id with same wire and came to .28ohms. Wicked with organic cotton and powered it up to 50 watts, this time I got…

Help with Crius RTA

Hot rx200s

My rx200s gets warm

After about five pulls. About 2.7 seconds per puff. Maybe ten to fifteen seconds between each puff.

Firmware: 4.12
Batteries: lg hg2
Wattage: between 50 & 70
Tank 1 : limitless plus 0.16
Tank 2: tsunami 24 0.18
Tank 3 limitless plus 0.18
Tank 4: goon 0.23

Uncomfortably hot.
I'm not sensitive. A man's man.

I can tolerate heat.

Perhaps I'll downgrade to back to 4.10

Mason dumptank 30 rta

Well I know why it's called a dumptank. It dumps <a href="http://www.vapininthecape.com/e<a href="http://www.vapininthecape.com/eliquid_c_7.html”>liquid_c_7.html”>juice out as fast as you can put it in! Using 2 3mm claptons, even put in 2 spacers under the silicon on the filler, rewicked it more than twice and still pours <a href="http://www.vapininthecape.com/e<a href="http://www.vapininthecape.com/eliquid_c_7.html”>liquid_c_7.html”>juice out of the AFC.

Sent from my SGH-M919 using Tapatalk

Phillips Screws for tsunami 24?

The hex screws for my tsunami 24 have all stripped out. It's possible I am over tightening or I got terrible screws…i know I'm using the correct tool because i checked the play etc before using the tool. I did not use the included tool because it' did not fit well in the grub screws.

Anyone know where I can pick up some Philips or flathead screws for it?

Sent from my SM-G900V using Tapatalk

Geekvape Avocado 24

Hello guys trying to dive into RTAs from a standard tank. I am a flavor chaser, planning kanthal coils between .8-1.2 ohm. I read that the fact an RTA is compact helps with flavor boosting, i also interested in the cotton set up of this RTA.

All the experienced RBAers, would you recommend this as a first RTA for me? And what do you think of its flavor compared to other RTAs on the average?

Low builds

i keep seeing people on YouTube building really low builds on the same device I use which is a Efusion duo. When I have 2 vtc4s the lowest its recommended to build is .17 I think but I see all these .1, .15 builds.

1 Does the lipo pack make it to where you can build lower? Never used a lipo so not sure what the lowest you can build.

2 Or are people using 18650s and just running cause it's in a regulated device? I have some builds I wanna use but it looks like it's going to put me around…

Low builds